Mining capacity: 4m 3 / day and night pressure: 20 MPa (200ÐºÐ³Ñ / кв.Ñм). Power is not more than 3KW Diameter: 117mm Length: 2700 mm Weight: less than 125kg
EDN5-6.3-1500 Electric Pump:
Mining capacity: 6.3m 3 / day and night pressure: 15 MPa (150ÐºÐ³Ñ / кв.Ñм). Power is not more than 3KW Diameter: 117mm Length: 2700 mm Weight: less than 125kg
EDN5-8-1300 Electric Pump:
Recovery: 8m 3 / Day and Night Pressure: 13 MPa (130ÐºÐ³Ñ / кв.Ñм). Power is not more than 3KW Diameter: 117mm Length: 2700 mm Weight: less than 125kg
EDN5-10-1200 electric pump:
Mining capacity: 10m 3 / day and night pressure: 12 MPa (120ÐºÐ³Ñ / кв.Ñм). Power is not more than 3KW Diameter: 117mm Length: 2700 mm Weight: less than 125kg
EDN5-12.5-900 Electric Pump:
Mining capacity: 12.5m 3 / day and night pressure: 9 MPa (90ÐºÐ³Ñ / кв.Ñм). Power is not more than 3KW Diameter: 117mm Length: 2700 mm Weight: less than 125kg
EDN5-16-750 Electric Pump:
Mining capacity: 16m 3 / day and night pressure: 7.5 MPa (75ÐºÐ³Ñ / кв.Ñм). Power is not more than 3KW Diameter: 117mm Length: 2700 mm Weight: less than 125kg
EDN5-20-600 electric pump:
Mining capacity: 12m 3 / day and night pressure: 6 MPa (60ÐºÐ³Ñ / кв.Ñм). Power is not more than 3KW Diameter: 117mm Length: 2700 mm Weight: less than 125kg
product description:
Used for low yield bending, inclined shaft oil extraction, practical for oil viscosity of not more than 50 CCT, paraffin content of not more than 6%, diameter of not less than 121.7cm.
Require well fluid indicator:
Associated water any content
Associated LPG maximum, 10
Hard content% (g / L) 0,2 (2)
Hydrogen sulfide content% (g / l) 0,001 (0,01)
Half-water hydrogen value рР6,0-8,5
Well fluid temperature о С 5-90о
advantage:
Pump high efficiency 27 to 40% (different models)
The main working parts are located in clean oil, well fluid isolation, wear small.
Wellhead installation is simple, single pump into the well.
No need to fix the ground and large base.
Small-diameter pump can be used to compress the tube, low maintenance costs.
Can be used for continuous production of very low production wells to avoid damage to the reservoir by periodic mining.
Use SHDN01-93U1-type control equipment.
Extend the time between well maintenance and increase output.
composition:
The UEDN5 package includes EDN5 electric submersible diaphragm pumps with 3 or 5.5 kW PEDD motors , ancillary equipment for control and protection, electrical contact pressure gauges, manometer tubes, sewer tubes and sewer tubes, note Liquid valve and with (spare) pieces. Depending on the structure and the type of motor, a standard sub-list of 14 devices is formed .
Compared with other manufacturers, our products have the following characteristics: The factory independent manufacturing and more major components - pumps, motors, control equipment. Parts have to undergo a rigorous test simulation test to ensure quality. Shelf life: 12 months from the date of installation.
Electric pump mechanism:
Type pump is a single pump EDN5 by a four-pole induction motor, speed reducer and a tapered piston pump with an eccentric drive and a round-trip spring components. All parts are in the same housing and the housing is filled with oil. Isolate the housing from the well using a rubber membrane and a compensator. The top of the pump is fitted with a connector for connecting the cable . Pumps are filled with oil and tested in the production facility.
SHDN 01-93 U 1 type supporting control equipment:
Control electric submersible diaphragm pump according to the set parameters to ensure that it does not deviate from the set value. Composition: a cabinet-type device, which contains the power distribution system, control system, and motor start-up, monitoring and disconnecting device. Control mode: manual, automatic control, remote control. The equipment has the following protection functions: 380V power system short-circuit protection; into a single maximum current value, can be any one of the current overload protection; leading to the pump can not improve the ground current protection; low voltage protection.
Electric contact pressure gauge:
Used to monitor the outlet pipe pressure, when the pressure is higher or lower than the set value, automatically cut off the pump.
Pressure gauge tube:
Used to connect the pressure gauge and the oil outlet pipe and protect the pressure gauge from well fluid damage.
Sludge pipe and upper sludge pipe:
Decompression rafts to protect the pump are not blocked by solids in the well fluid.
network:
Used to prevent solids from falling to the gas separator and suction valve.
Injection valve:
Used to inject liquid from the cavity of the pump compression tube when lifting the pump from the well.
With (spare) parts:
For routine repairs. Includes: a diaphragm, a suction valve, a pressure relief valve, four centrifugal bearings , two seals and other consumables.
Their respective countries: Russia Manufacturer: STARKY
Address: 426062, Russia, Izhevsk Sports Road 111
Underbody Structural Parts Of Rail Car Body
Most of the structural parts in this category are small, medium and large parts, which are mainly installed at the bottom of the car body to improve the bottom structure of the car body. All of them are metal products, and the materials are mostly aluminum alloy and stainless steel. They are painted or coated according to requirements The company is the source manufacturer, non-standard customization, most of the products can be customized in size and shape.
Jilin Zexin Industrial Development Co., Ltd. was founded in 2001 with a registered capital of 5 million RMB and is a high-tech enterprise in Jilin Province. There are about 100 employees, and the company's sales volume reached 20 million RMB in 2022. The company has more than 30 sets of various equipment including 2 NC laser cutting machines, 6 NC machining centers, 8 welding machines for different purposes, NC cutting machines, NC bending machines and others. After more than 20 years of construction and development, it has formed a comprehensive enterprise of electrical system, carbon steel, stainless steel and aluminum alloy stamping, welding, machining and surface coating. The company has passed the ISO9001:2015 quality management system certification, EN15085 CL1 welding system certification, American standard AWS welding certification, and ISO/TS22163:2017 quality management system certification. It is a high-quality supplier cooperated by CRRC Changchun Railway Vehicles Co., Ltd., the core manufacturer of China's urban rail transit equipment and high-speed train.
Underbody Structural Parts Of Rail Car Body,Single Hole Single Tube Buckle,Single Hole Double Tube Clamp,Large Metal Reinforcement Board
Jilin Zexin Industry Development CO., LTD. , https://www.jilinzexin.com