1, pump leakage reasons
(1) When installing the pump, the water seal seat assembly is not installed in place, causing the pump to continue to leak. As with the hole corresponding to the inspection hole block (rejection) hydrosphere, when the water seal leaks, the cooling water shaft along the water ring will be thrown out from the pump hole and drip, so as to prevent Cooling water flows into the bearing to destroy lubrication. In addition, the replacement of the retaining ring does not pay attention to clear the pump body and the pump cover can not be well combined and sealed, will result in water leakage pump.
⑶ poor working environment of construction machinery, easily lead to uneven wear bushing seals and bushings end surface; spring immersed in water for a long time, easy to rust, decreased elasticity, can also cause water leakage.
â‘· winter forget to put water or water is not clean, and when the water temperature is too high, the cooling system after the condensation of water vapor freezing, are likely to cause pump body was frozen, leading to water leakage.
⑵ old machines, sealing parts wear, corrosion and aging failure, is also the cause of the pump leaks. When the construction machinery is parked for a long period of time, there is no cooling water in the engine, causing the bakelite gasket to deform due to the dry knot and shrinkage. Although the bakelite gaskets will expand but not fully restore the original shape after the water is added, it will cause a small amount of water leakage. In addition, for newly installed pumps, bakelite gaskets and cast iron bushings have not yet fully run together, will also lead to a small amount of water leakage pump.
2, emergency measures
If it is found that the water pump of the working engine is leaking, it shall not stop its work immediately, keep it at the lowest steady speed, and add water to the inside of the cooling system to drain water. (Note: When opening the water inlet cap, put a Cover, to prevent being scalded by the steam), the engine cooling, short period of time, slow driving, driving to the nearby shelter and then ruled out. If it is a sudden encounter with the pump casing rupture and leakage, or damage to pump parts and lost pump water role, may be appropriate to replace the relevant parts, troubleshooting.
If the pump damage is very serious, the way there is no repair conditions, the pump can be directly connected to the inlet and outlet to take full advantage of the natural circulation of hot and cold water to temporarily maintain the engine to maintain normal temperature; or use a tube or bucket as Container, firmly fixed, and then leads two hoses from the container, one connected to the engine inlet, the other connected to the engine outlet, the other end of the two tubes are inserted into the container , And should be fixed hose.
If only the pump casing cracks and leaks, cracks can be handled clean, and then use adhesives to make up. In order to emergency, available egg mixture of cement mixed into a sticky group smear in the cracks, to be solidified a few minutes before you can use.
Construction machinery driving or work process, the water pump water leaks are also commonplace. As long as there is no rejection of water ring damage or swelling deformation, inadequate spring seal water pressure or broken and other failures, can carry out emergency treatment. Specific measures for emergency response is: If the water seal due to the seal is not strict there is a slight leakage, but the wear is not too serious, you can shop in a glass or flat sand cloth, the sealing surface of water seal grinding can be smooth; Bakelite seal can be flipped before use. However, both should be noted that the water seal and the pump body contact surface should be ground to ensure its sealing performance.
MC Wall series Wall Hanging led display
P1.66, P1.875, P1.923, P2, P2.5, P3.07, P3.91
Wall Hanging led display classical and stable structure and performance.
1. Two protected strong locks design, realizing
combination of reliability and security.
2. Die-casting aluminum body, lightweight for easy
transportation and high accuracy installation.
3. Perfectly be compatible with any existing controller
and without screen shaking/quick flashing/mosaic problems.
4. Supporting installation of hanging/ground mounting,
for stage/TV show/studio, and other event applications.
Wall Hanging Led Display is highly usable at indoor places like Airport, subway station,malls, stages, chain stores, hotels, public buildings, bars, restaurants, etc. Its thin size and ultra-lightweight module makes it easy to install at any area without covering much space.
Wall Hanging Led Display,LED Wall Display,Movable Wall Hanging LED Display,Wall Hanging Small LED Display
Shenzhen Macion Optoelectronics Technology Co.,Ltd. , https://www.macion-led.com