First, the types of tiles and introduction Here I learned about the general, for your reference:
1. Polishing and turning: This kind of brick is pressed with clay and stone powder by a press and then fired. The front and back sides have the same color and no glaze. After burned, the surface is polished again. It is very smooth and beautiful, and the back is the original appearance of the brick. Polish everyone knows? For example, the stone floor and the wall surface are polished and the province is not bright. However, after polishing, it looks very bright. Since it is polished, the problem will follow, because it is smooth, bright, so it is not resistant to dirt, after dragging with a mop, will leave a mark of water, because your mop is not 100% Clean, like a glass, so if you want to clean, it is more time-consuming; the second drawback is that polishing is smooth, so it does not slip, that is once there is water on the ground, it is very Slippery, which is why everyone sees the stone in the building where the general staircases and other places are not thrown into light, but matt, only in this way can slip. The third problem is that the color liquid is easy to infiltrate. The simplest test is to take a pen to write a few words on the surface of the brick. The poor polish turns and wipes off immediately after writing. It is not necessarily clean. The writing may have penetrated. A good brand, because the press is good, the density is high, plus the high temperature of the firing, the density is very high, so it is not easy to infiltrate, but this is not absolute, no matter how good the polishing turn, if you write the word 10 After a few minutes of rubbing, there will be traces that will never be removed because the ink has penetrated into the brick.
2. Corrugated bricks: Corrugated bricks are similar to polished ones, but their production requirements are higher, they require better presses, and they can suppress higher densities. At the same time, the firing temperature is higher, and all ceramics can be made. The waved brick is an enhanced polished turn, the surface is generally no longer need to be polished, it is very bright, to a certain degree to solve the problem of polishing turn dirty. Of course, the price of waved bricks is more expensive than polishing. Summary: Polished and oscillating bricks are beautiful because of their bright surface, and they have high wear resistance. However, they have the disadvantages of single color, easy to be dirty, non-slip, and easy to infiltrate colored liquid. These two types of bricks are generally relatively large. Used in the living room, entrance court and other places, it is rarely used in places such as bathroom and kitchen.
3, glazed tiles: As the name suggests, is the surface with the glaze fired together with the layer, the main body is divided into two kinds of clay and porcelain clay, clay out of the back of the red, called tiles, porcelain back firing back was gray, called Tiles, usually made of china clay, have a good effect, so a good brick is called a tile instead of a tile. The surface of the glazed tile can be made with various patterns and patterns, which is richer than the color and pattern of polishing, because the surface is glaze, so the wear resistance is not as good as polishing. In addition to the size of the glazed tile identification indicators are the same, etc., mainly to see the water absorption rate, generally good bricks, presses, high compression density, high firing temperature, good porcelain, so the water absorption rate is also small. The disadvantage of high water absorption rate is that it is easy to seep into the liquid, and some even when the tiling is done, it can suck in the dirty water from the back and enter the glaze. At the same time, the water absorption rate is high, and the glaze and the embryonic body are easily cracked. If the bad brick is used for a period of time, the surface at the foot will fall off, which is caused by the temperature and humidity inconsistent changes in the glaze and the embryonic body. So the better tile, the lower the water absorption rate, people who don’t understand think that the tiles are similar, but it will not work after a few years, especially the toilet. The principle is the same as the ceramic tile. If the glaze on the surface is not good, it is easy to hang. If there is a high water absorption rate in the toilet, the stolen goods will slowly infiltrate into the toilet. In a year or two, you will find that your toilet is flushed. How can you smell it? The smell is actually from the toilet itself. Yeah, worse toilets will drop after a year or two later, where the water will fall. I've seen some people's toilets. Such toilets can only be changed. Therefore, many things for decoration are not but good or bad, but there will be a difference after a year or two. How do you say it, or a penny and goods? Glazed tiles are commonly used in kitchens and bathrooms, with rich color patterns, and tiles that have been treated to prevent slippage. Glazed tiles are generally not large, but they can be very small, such as small to mosaic, but too small tiles, construction costs are generally more expensive.
Second, choose the method of tile:
A look at the specifications, a few blocks of good bricks fall together, the same size, but to tell the truth, most of the domestic brick size is not very good, a few pieces of brick put together, usually the size is not the same, if very different The posted effect can be imagined. Secondly, the water absorption rate is generally as small as possible. As long as some water is poured behind the tiles, it is easy to see that if the water is absorbed all at once, it is because the water absorption rate is high and the possibility of future problems is very high. If water penetrates very slowly or slowly, bricks are better and the water absorption is low. You can also listen to the sound, but this trick is not used by non-industry people because everyone listens too little and doesn't feel it.
1. Polishing and turning: This kind of brick is pressed with clay and stone powder by a press and then fired. The front and back sides have the same color and no glaze. After burned, the surface is polished again. It is very smooth and beautiful, and the back is the original appearance of the brick. Polish everyone knows? For example, the stone floor and the wall surface are polished and the province is not bright. However, after polishing, it looks very bright. Since it is polished, the problem will follow, because it is smooth, bright, so it is not resistant to dirt, after dragging with a mop, will leave a mark of water, because your mop is not 100% Clean, like a glass, so if you want to clean, it is more time-consuming; the second drawback is that polishing is smooth, so it does not slip, that is once there is water on the ground, it is very Slippery, which is why everyone sees the stone in the building where the general staircases and other places are not thrown into light, but matt, only in this way can slip. The third problem is that the color liquid is easy to infiltrate. The simplest test is to take a pen to write a few words on the surface of the brick. The poor polish turns and wipes off immediately after writing. It is not necessarily clean. The writing may have penetrated. A good brand, because the press is good, the density is high, plus the high temperature of the firing, the density is very high, so it is not easy to infiltrate, but this is not absolute, no matter how good the polishing turn, if you write the word 10 After a few minutes of rubbing, there will be traces that will never be removed because the ink has penetrated into the brick.
2. Corrugated bricks: Corrugated bricks are similar to polished ones, but their production requirements are higher, they require better presses, and they can suppress higher densities. At the same time, the firing temperature is higher, and all ceramics can be made. The waved brick is an enhanced polished turn, the surface is generally no longer need to be polished, it is very bright, to a certain degree to solve the problem of polishing turn dirty. Of course, the price of waved bricks is more expensive than polishing. Summary: Polished and oscillating bricks are beautiful because of their bright surface, and they have high wear resistance. However, they have the disadvantages of single color, easy to be dirty, non-slip, and easy to infiltrate colored liquid. These two types of bricks are generally relatively large. Used in the living room, entrance court and other places, it is rarely used in places such as bathroom and kitchen.
3, glazed tiles: As the name suggests, is the surface with the glaze fired together with the layer, the main body is divided into two kinds of clay and porcelain clay, clay out of the back of the red, called tiles, porcelain back firing back was gray, called Tiles, usually made of china clay, have a good effect, so a good brick is called a tile instead of a tile. The surface of the glazed tile can be made with various patterns and patterns, which is richer than the color and pattern of polishing, because the surface is glaze, so the wear resistance is not as good as polishing. In addition to the size of the glazed tile identification indicators are the same, etc., mainly to see the water absorption rate, generally good bricks, presses, high compression density, high firing temperature, good porcelain, so the water absorption rate is also small. The disadvantage of high water absorption rate is that it is easy to seep into the liquid, and some even when the tiling is done, it can suck in the dirty water from the back and enter the glaze. At the same time, the water absorption rate is high, and the glaze and the embryonic body are easily cracked. If the bad brick is used for a period of time, the surface at the foot will fall off, which is caused by the temperature and humidity inconsistent changes in the glaze and the embryonic body. So the better tile, the lower the water absorption rate, people who don’t understand think that the tiles are similar, but it will not work after a few years, especially the toilet. The principle is the same as the ceramic tile. If the glaze on the surface is not good, it is easy to hang. If there is a high water absorption rate in the toilet, the stolen goods will slowly infiltrate into the toilet. In a year or two, you will find that your toilet is flushed. How can you smell it? The smell is actually from the toilet itself. Yeah, worse toilets will drop after a year or two later, where the water will fall. I've seen some people's toilets. Such toilets can only be changed. Therefore, many things for decoration are not but good or bad, but there will be a difference after a year or two. How do you say it, or a penny and goods? Glazed tiles are commonly used in kitchens and bathrooms, with rich color patterns, and tiles that have been treated to prevent slippage. Glazed tiles are generally not large, but they can be very small, such as small to mosaic, but too small tiles, construction costs are generally more expensive.
Second, choose the method of tile:
A look at the specifications, a few blocks of good bricks fall together, the same size, but to tell the truth, most of the domestic brick size is not very good, a few pieces of brick put together, usually the size is not the same, if very different The posted effect can be imagined. Secondly, the water absorption rate is generally as small as possible. As long as some water is poured behind the tiles, it is easy to see that if the water is absorbed all at once, it is because the water absorption rate is high and the possibility of future problems is very high. If water penetrates very slowly or slowly, bricks are better and the water absorption is low. You can also listen to the sound, but this trick is not used by non-industry people because everyone listens too little and doesn't feel it.